CHAPTER 3 LAB 3-7 OSPF CASE STUDY ANSWERS

Configure OSPF with the networks shown in the diagram. Configure R2 to summarize area 20 with the most specific mask possible. Configure area as an NSSA. The table does not include any other type of interface, even though a specific router might contain one. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab. You can use other routers such as or and Cisco IOS Software versions if they have comparable capabilities and features. Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device.

To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. Explanation of Selected Requirements — Instructor Version The requirement to address a hidden issue in the topology to have full connectivity means that you must build a virtual link across area 23 to have area 34 connected to the backbone. Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. The table does not include any other type of interface, even though a specific router might contain one. Use the addressing scheme shown in the diagram. Summarize this area with the most efficient summary.

chapter 3 lab 3-7 ospf case study answers

To find out how the router is configured, chaptef at the interfaces to identify the type of router and how many interfaces the router has. Notify me of new posts by email. Summarize this area with the most efficient summary.

  SOAS MSC DISSERTATION GUIDELINES

CCNP Route Lab 3-7, OSPF Case Study

Make the link between R2 and R3 have a cost of Configure R1 to always originate a default route. Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Notify me of new posts by email. Notify me of follow-up comments by email.

chapter 3 lab 3-7 ospf case study answers

Configure the Frame Relay subnets as point-to-point subinterfaces, with the link between HQ and East in areaand the link between HQ and West in area Verify that all configurations are operational and functioning according to the guidelines. The table answesr not include any other type of interface, even though a specific router might contain one.

Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. You can use other routers such as a or and Cisco IOS Software versions if they have comparable capabilities and features. Figure out the hidden issue in the topology that you need to address to have full connectivity.

(PDF) CCNP TSHOOT Instructor Lab Manual | Francisco Montes –

Configure area 34 to be a totally stubby area. The table does not include any other type of interface, even though a specific router might contain one. Configuration Requirements Configure the interfaces in the diagram with the IP addresses shown.

Design, configure, and test a network that meets all the following requirements: Design, configure, and test a network that meets all the following requirements:. To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has.

  LANCIA THESIS 2.4 JTD WIKI

Configure area as an NSSA. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.

Configure OSPF with the networks shown in the diagram. Notify me of follow-up comments by email.

Explanation of Selected Requirements — Instructor Version The requirement to address a hidden issue in the topology to have xase connectivity means that you must build a virtual link across area 23 to have area 34 connected to the backbone.

Configure R2 to summarize area 20 with the most specific mask possible. You can use other routers such as or and Cisco IOS Software versions if they have comparable capabilities and features. Use the addressing scheme shown in chaptsr diagram. Configure the bandwidth to reflect the actual bandwidth of all stydy links. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.

Modify the link between R2 and R3 to have hello timers and dead timers that are double the default values. Configure OSPF with interfaces in the areas shown in the diagram.

Make sure that all loopback interfaces are advertised with the correct subnet mask. Run a Tcl script on all routers to verify that there is connectivity between the IP addresses in the topology.

chapter 3 lab 3-7 ospf case study answers

Configure the router East loopback interfaces to be in area